Proxy checker
Paste up to 20 proxies and see for each one whether it works, the exit IP with its country and network, the exit OS by TCP/IP fingerprint (p0f) and whether it matches the OS of your browser.
Results
| Proxy | Status | Latency | Exit IP | OS: exit / browser | Risk |
|---|
On ipv.rent static IPv4 proxies the exit OS profile (p0f) switches to Windows, macOS or Android at no charge, in every package.
Static IPv4 proxies →What the proxy checker shows
The checker connects through each proxy on your list and reports whether the connection works, how long the check took, which IP address sites see and where that address is. For a working proxy it also estimates the operating system of the exit from TCP/IP parameters (p0f) and compares it with the OS of your browser.
Working and risk are separate results. A proxy can connect without problems and still get a high risk level: for example, when its exit looks like Linux while the browser profile says Windows.
How to check a proxy
-
Paste the list
One proxy per line, up to 20 lines. Supported formats: ip:port, ip:port:user:pass, user:pass@host:port and scheme://user:pass@host:port.
01 -
Protocol and OS are detected for you
The checker tries HTTP first and SOCKS5 if that does not connect. A scheme in the line sets the protocol explicitly. The OS to compare with comes from your browser.
02 -
Run the check
Lines are checked two at a time, and each result appears as soon as it is ready. A line with a format error is not sent.
03
What each value means
- Status
- "Working" means a connection through the proxy was established. "Could not connect" covers a wrong login or password, a closed port, a host that does not exist and a timeout: the check cannot tell these cases apart.
- Latency
- How long the check through the proxy took, measured by the checking server along its own route. It does not show the speed from your device.
- Exit IP and location
- The address sites see. Country, region and network (ASN) come from the GeoLite2 database. For some addresses the database has no city or no record at all, and the page then shows "no data".
- Network OS (p0f)
- An estimate of the exit operating system from TCP/IP parameters: TTL, window size, MSS, the order of TCP options. It is a guess, not a determination. macOS and iOS look the same at this level.
- OS match
- Compares the network OS with the OS you selected. With "Do not compare" selected, the check covers the network only.
- Risk
- An overall estimate from clean to high, based on the anomalies found. Every anomaly is listed under the result with its own explanation.
Typical problems and what to do
The network OS does not match the browser
The most common case is a datacenter proxy with a Linux exit used in a Windows or macOS profile. Choose a proxy whose exit profile matches your OS. On ipv.rent static IPv4 proxies the exit profile is switched on the package page at no charge.
The proxy does not connect
Check the address, port, login and password. The checker tries HTTP and SOCKS5 itself; for an HTTPS proxy add the https:// scheme. A proxy that only accepts whitelisted IP addresses will not pass: the check connects from a checking server, not from your device.
High risk on a working proxy
Open the line and read the findings. An OS mismatch is fixed by choosing a matching OS profile. A listing in proxy databases is fixed only by changing the address.
The line is rejected
If the password contains a colon, the ip:port:user:pass format becomes ambiguous: use scheme://user:pass@host:port. Private and reserved addresses such as 10.0.0.0/8 or 192.168.0.0/16 are not checked.
How the check works
Each line goes to our server as a separate request. The server parses it, rejects private and reserved addresses and starts the check: a connection is made through the proxy to a measurement server, which reads the parameters of the exit. The result contains the address, port and protocol of the proxy, but not the login and password.
The exit IP, latency and TCP/IP parameters are measured on that connection. Location and network come from the GeoLite2 database. The exit OS and the risk level are estimates based on these parameters, not established facts about the proxy.
Proxy credentials are sent over HTTPS only for the check and are not stored: not in a database, not in the address bar, not in browser storage. The results disappear when you press Clear or close the page.
Questions about the proxy checker
Which proxy formats are supported?
ip:port, ip:port:user:pass, user:pass@host:port and scheme://user:pass@host:port, where the scheme is http, https or socks5. The host can be an IP address or a domain name; an IPv6 address goes in square brackets.
Can I check a proxy with a login and password?
Yes. Put them in the line in one of the supported formats. If the password contains a colon, use scheme://user:pass@host:port so the line can be parsed unambiguously.
Do I need to specify the protocol?
No. The checker tries HTTP, then SOCKS5, and shows which one connected. It does not change the port: if HTTP and SOCKS5 run on different ports, check each address and port pair. For an HTTPS proxy add the https:// scheme.
How long does a check take?
A working proxy usually takes a few seconds. A proxy that does not respond is given up to 15 seconds. When many people check at the same time, a line waits a few seconds and is retried automatically.
What does the risk level mean?
It estimates how suspicious the connection looks to anti-fraud systems, from clean to high, based on the anomalies found: an OS mismatch, unusual TCP/IP parameters, a listing in proxy databases. High risk does not mean the proxy is down, and a clean result does not guarantee that sites will not block it.
Where do my proxy credentials go?
Over HTTPS to our server and to the measurement server, only for that check. We do not store them and do not send them to analytics. Details are in the privacy policy.
How many proxies can I check?
Up to 20 lines per run. The number of checks from one IP address is limited: when the limit is reached, the page asks you to wait a few minutes.
This product includes GeoLite2 data created by MaxMind, available from https://www.maxmind.com.
Ready to connect your first pool of IPs?
Signing up takes 2 minutes, credentials arrive less than a minute after payment.
or email us at [email protected] — reply within 2 hours